Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)K

Koopa_Khan

@ Koopa_Khan @lemmy.world

Posts
8
Comments
33
Joined
3 yr. ago

  • Motherboard swap!

    Jump

  • Instructions unclear, I’ve given the whole printer a bath and now all it does is blow bubbles

  • Motherboard swap!

    Jump

  • Thank you! I’ll take a peak at it!

  • Motherboard swap!

    Jump

  • Thank you! Its the perfect size for things like this

  • Motherboard swap!

    Jump

  • I appreciate the info! I’ll be honest, I understand wiring and hardware but I get out of my depth once we start getting into firmware and software.

    I’m thanking my lucky stars that Octoprint was as easy as it was. That being said, if that open source ams makes any progress, I might just reach out since it seems like klipper is the only thing it’ll work with. If you don’t mind, I may reach out when I get the courage up to give it a shot.

  • Motherboard swap!

    Jump

  • I appreciate your confidence in me, but I don’t think up for trying to learn how to deal with it. I don’t do well with troubleshooting firmware/software when things go tits up

  • Motherboard swap!

    Jump

  • Thank you!

    I have a pi 4b running octoprint hooked up. Is there any advantage to going the klipper route?

    In theory it shouldn’t mater if i use 4.2.2 firmware on the 4.2.7 board right?

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    Motherboard swap!

  • Clogged nozzle?

    Jump

  • Nope, just a very moody Ender 3v2 Neo

  • Clogged nozzle?

    Jump

  • It looks like my perimeter speed is 40 mms and my infill is 50mms

  • Clogged nozzle?

    Jump

  • Thank you for the tip! I just checked, it looks like it was disabled so that wasn’t my issue. I wonder why it was causing you issues though

  • Clogged nozzle?

    Jump

  • It is PETG. That’s good to know. I’ve got a few more prints on the docket so switch to gyroid and see how that goes. Thanks for the tip!

  • Clogged nozzle?

    Jump

  • I’ll have to go back and look at the slicer settings, but I can tell you the info is much faster than the wall just watching it go. Would you recommend upping the flow rate or my better to slow down the printhead speed?

  • Clogged nozzle?

    Jump

  • Good call I’ll have to take a look. I wish I could’ve copied the profile from the Creality slicer into Prusa Slicer, but creality keeps crashing.

  • Clogged nozzle?

    Jump

  • Thanks for the other tips. I’ve tried a cold pole with the last filament to see if we could get anything out of there and I think we should be good, but you never really know.

    As far as the rest of it, it seems to be happening with every filament I slice in Prusa slicer.

    This was a brand new filament I had opened from Micro Center, it’s just their generic inland filament and it looks like the humidity in my dry box is about 16% after running it through my dryer. Maybe it’s too dry lol.

    To be honest, I didn’t think about replacing the nozzle that’s probably a good idea. I got this printer from an auction site used so I can only imagine it’s the original nozzle from who knows how long ago

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    Clogged nozzle?

  • Deleted

    Permanently Deleted

    Jump

  • Does he still work there?

  • Framing cleaning help

    Jump

  • Thanks again, will do! I think we’re gonna try and get it in next week so I’ll keep you update when we get it wrapped up!

  • Framing cleaning help

    Jump

  • I think that settles it for us, we’ll likely take it to a framers when we get home. I’m a bit scared to try and dismantle it myself.

    Thank you for the advice!

  • Framing cleaning help

    Jump

  • Thank you!

  • Art Share🎨 @lemmy.world
    Koopa_Khan @lemmy.world

    Framing cleaning help

  • Thank you!

    Jump

  • I’m considering an a change at point as well. The v2 has been great but finicky is a perfect description. Any reason you were thinking Bambo Labs instead of a Prusa?

  • Thank you!

    Jump

  • Of course! This should be the original link. I think my issue was slightly different, but hopefully this helps. My stepper motors were over heating and skipping steps. If it looks like that might solve your issue, this article helped with my ender 3

    Thank you! I appreciate it!

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    Thank you!

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    The art and the artist

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    Which slicer do you use

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    How?

  • 3DPrinting @lemmy.world
    Koopa_Khan @lemmy.world

    Ender 3 V3 Neo Enclosure