Skip Navigation

InitialsDiceBearhttps://github.com/dicebear/dicebearhttps://creativecommons.org/publicdomain/zero/1.0/„Initials” (https://github.com/dicebear/dicebear) by „DiceBear”, licensed under „CC0 1.0” (https://creativecommons.org/publicdomain/zero/1.0/)E

ExcessShiv

@ ExcessShiv @lemmy.dbzer0.com

Posts
19
Comments
1818
Joined
2 yr. ago

  • Fra i dag bliver kommunerne sat fri [på jobcenter-området]: 'Nu er det den faglige dømmekraft, der skal være i højsædet'

    Jump

  • Det tror jeg ikke...jobcentrene har i mange år været plaget af tåbelig topstyret lovgivning lavet af politikere der ikke aner en skid om området. Det kan næsten kun blive bedre nu end det tidligere har været. Dem jeg kender som arbejder på området ser umiddelbart frem til ikke at skulle tvinge borgere til dumme meningsløse møder, praktikker osv.

  • The TV industry finally concedes that the future may not be in 8K

    Jump

  • It was the same when movies started getting released in 1080p back in the day, it just looked weird

  • The TV industry finally concedes that the future may not be in 8K

    Jump

  • No, not really. "2K" is 2560x1440 resolution, it's almost twice the pixel density for similar sized monitors.

  • Why is the SLZB Ultima so Cheap? is there a catch?

    Jump

  • I never communicate with sellers, I always just open a dispute right away. I'm not bothering spending days going back and forth due to time differences and language barriers, fuck that.

  • Can you tell when the dry filament started being extruded?

    Jump

  • Probably not, I've seen reviews online (after I bought it) that complains about it only printing matte at lower temperatures but then is isn't possible to print fast anymore.

  • Can you tell when the dry filament started being extruded?

    Jump

  • This is the only PETG I've ever had this issue with, normally I can just store them with dessicant and it's fine.

    Right now RH is fairly low around 30-40% because it's cold and winter, summer its usually around 60-80% here.

  • Can you tell when the dry filament started being extruded?

    Jump

  • They do state it is more hygroscopic than normal PETG due to additives that allow the fast printing, but this is still significantly worse than I ever expected. I also didn't expect to need to dry it for two days after unwrapping it just to print with it.

  • Can you tell when the dry filament started being extruded?

    Jump

  • Its Sunlu HS PETG, relative humidity is a little under 40% in the room (around 25% in the storage box), there's probably about 60-70cm from dryer to extruder. I already purged a good amount before starting the print, but apparently not enough.

  • Why is the SLZB Ultima so Cheap? is there a catch?

    Jump

  • you have zero recourse if you get screwed aside from leaving bad reviews.

    I've had a few bad experiences with sellers over the past decade with aliexpress, a couple hundred orders in total, but when there was any issue I've always received a full refund within a few days. only once did I experience a seller disputing my refund claim, but aliexpress got involved and I got the full refund.

  • Guitar technology

    Jump

  • Unfortunately it needs a safety cage around the bottom end

    Only if you're a scared little bitch /s

  • Can mere dirt cause heatcreep?

    Jump

  • I have an old v6 hotend with about 2500h of print time on it, looking pretty dirty too, but I have no issues with heat creep. I also don't think that what you show should be causing heat creep, but giving things a good thorough cleaning occasionally is never a bad idea.

  • Server ROI Calculator

    Jump

  • I think the ROI for my server is something like 6-7 years, not counting the electricity it uses. I don't do it to save money but to gain independence, which is good because realistically it will never break even.

  • [2026-01-30] Fri snak fredag

    Jump

  • Spiser du så heller ikke varm mad om sommeren?

  • Sverige vil fængsle brugere af ulovlig IPTV

    Jump

  • men i min position

    LOL 🤣

  • The long read: What technology takes from us – and how to take it back | Rebecca Solnit

    Jump

  • You misunderstand me then...I'm not saying we should not regulate some technologies and what they're allowed to be used for, we absolutely should. But blame should be put solely on the people using it in horrible soul crushing ways. They are terrible people doing terrible things, blame them, punish them.

  • Tesla's 'unsupervised' Robotaxis vanish a week after pre-earnings announcement

    Jump

  • He may have used "end of year" before 2018...I'm pretty sure he promised "coast-to-coast" FSD capabilities "by end of the year" back in 2016

  • Sverige vil fængsle brugere af ulovlig IPTV

    Jump

  • Min kommentar var også på at det altid er ulovligt fordi du altid uploader, hvilket ikke er korrekt. Det er altid ulovligt fordi rettighedsalliancen er virkelig gode til at fordreje virkeligheden med deres lobbyisme. Bare det, at de sidestiller det med tyveri fordi du jo så ikke har købt det i stedet er jo grundlæggende forkert. Folk der benytter sig af torrent downloads ville oftest slet ikke have købt det selv hvis de ikke kunne hente det gratis andre steder, så der er reelt oftest slet ikke et tabt salg som de påstår.

  • The long read: What technology takes from us – and how to take it back | Rebecca Solnit

    Jump

  • Because technology isn't to blame. Technology doesn't have any agenda or intrinsic capacity for malice...the people behind it do. The people who decide to use the capabilities of technology with malicious intent are to blame, they should be blamed for all of it. Do not let technology share the load of that blame, it is only the people behind that should that, they er personally to blame because they actively chose to use technology maliciously when they could just have chosen not to.

  • Tesla's 'unsupervised' Robotaxis vanish a week after pre-earnings announcement

    Jump

  • This is the same CEO who has promised “full self-driving next year” every year since 2018.

    This is just plain lying by electrek...he started promising "self-driving next year" long before that.